T870A BGA IRDA Welder Infrared Heating Rework Station Start Price USD 915.00 Current Price USD 915.00 Time Left - Bid Count 0 Buy It Now Price - Reserve Price - Start Time Sunday, August 24, 2008 End Time Wednesday, September 03, 2008 Location cn See more about 'T870A BGA IRDA Welder Infrared Heating Rework Station' Description accuni-express store T870A BGA IRDA Welder Infrared Heating Rework Station Features1、Adopt infrared weld technology which independent exploration.2、Use infrared heat,easy to cut through,heat proportion piercing tradition weld machine with sirocco.3、Easily operate.Just need one day training.Can operation this machine.4、Don't need weld tools.This machine can weld all the component of 35-50cm.5、This machine has 800W heating system.widely to240x180mm.6、Infrared heating don't have sirocco flow. Don't impact perimeter small component.Can suitable for all of the component,especially Micro BGA component.7、Definitely can satisfy the computer, the notebook, the electricity swims and so on the BGA sealing off/repairs to request；Specially especially suits to the computer north and south bridge。 Technic parameter Work floor size 360X240mm Rated voltage and frequency AC220-230v 60/50Hz Complete machine power 1000W Infra-red lamp body power 150W Preheating chassis power 800W Infra-red lamp body heating size Φ70mm(50x50mm) Preheating chassis preheating size 240x180mm Infra-red lamp body temperature adjustable 200℃-350℃ Preheating chassis temperature adjustable 60℃-200℃ Instrument inventory Welding table main body 1 Infra-red lamp body 1 Temperature sensor 1 Board support of the circuit 1 Power line 1 user's manual（Compact disc） 1 1.Inspect the machine and then open it (1) Check if the connection wire of the lamp body, the Temp-sensor and power cable is ok. (2) Turn on the power switch. Allow the T-870A Power-On-Self-Test (POST) to complete. After this, Temperature set-points will display last value used. (3) The front panel has two switches, controls the preheating dish and the infra-red lamp body separately; 2. PC Board Component Removal and Replacement (1) Placed the PCB Board Put the PCB board on the “PCB board holder”, rotate the “holder fasten nut”, fasten it. Move the “PCB board holder” to choose the right position. (2)the Process of unsoldering and repairing ①Adjust the position of the PCB board, make the chip at the centre of the lamp light. Adjust the height of the lamp body, keep the lamp 20-30mm from the chip. ②Put the temp-sensor at the edge of the chip, lay a bed of solder flux around the chip and on the temp-sensor, it will make the measured temperature more accurately, at the same time the solder flux will make the soldering chip more perfect, and keep the bonding pad away from conglutinating and having tin wool. ③According to the producing technological requirement or the size of PCB board, adjust the pre-heat dish temperature(adjustable 60-200℃). When there is waterproof solid sealing compound on the chip, please open the pre-heat dish to pulverize the solid sealing compound first, then clean it up. You may adopt other method as sol/hydrosol. When you adopt the method we supplied, you had better choose the temperature between 100℃ and 140℃according to the producing technological requirement or the size of PCB board, control the pre-heat time 3-5 minutes(the temperature will be steady) or longer. Otherwise if the chip is without waterproof solid sealing compound or the PCB board is small, then it won’t transmutation, we needn’t open the pre-heat dish ④According to the producing technological requirement or the size of chip, choose the suitable temperature of the IR-lamp. ⑤Usually, when the chip size is less than 20*20mm, we adjust the IR-lamp temperature 220-240℃, and if the chip is without waterproof solid sealing compound or the PCB board is small, then it won’t transmutation, we needn’t open the pre-heat dish. Otherwise, we should adjust the pre-heat temperature to 100-120℃. When the chip is lager than 30*30mm,we should adjust the pre-heat temperature to 120-140℃ first, wait 3-5minutes and the temperature will be steady. Then adjust  the IR-lamp temperature to 240-260℃, we will complete the unsoldering and repairing process conveniently. Attention: At the time, the light is strong, the temperature rises quickly, we should pay our attention on controlling, avoid the Temp-sensor displacement, reflect on the temperature measuring. We should also pay our attention on time controlling, avoid burning out the chip. ⑥When achieving the set-up lamp temperature, Once the solder liquefied and melted, use tweezers to remove the chip.     3.the Process of Soldering a chip It is generally the same as the “(2)Process of unsoldering and repairing”, but you should do as follows: ①Clean the target pad with the brush ②Then put the solder ball and a flat of solder flux and the chip on the target pad ③ Turn on the switch of the pre-heat dish, and set-up the temperature ④Turn on the switch of the IR-Lamp, Regulate the temperature (the temperature must be warm enough to liquefied the solder), focus the Infrared light on the chip to be solder ⑤ Wait to allow the Infrared lamp to heat the solder flux to work as the solder balls on the target chip pad reaches liquid temperature. Use tweezers or a vacuum device to place the chip target position. Once the solder liquefies, the chip will be sold automatically. After cooling the chip, pick up the PCB board, check if it is ok. If not, re-operate. Suggestion: About the components without plumbum, you should add 20-30℃. 4. the Process of soldering kinds of Plug (as: GAP platoon expansion slot plug of the computer motherboard) Usually we cover the hardware and the PCB board (which won’t be maintained) with the aluminium-foil paper, Then put the PCB board on the holder, fasten it. Turn on the Pre-heater dish and adjust the temperature at 160-180℃, Put the Temp-sensor at the side of the part which is being unsoldering, and it will up to the temperature in 3-5minutes. Then you can unsoldering the parts. In special circumstances, you can open the IR-Lamp to heating the part, and it will be unsoldering quickly. Suggestion: About the components without plumbum, you should add 20-30℃. About the PCB board with components on its both side, please set-up the pre-heat temperature lower, and then use the IR-Lamp to heat. 5. Cooling the machine Turn off the switch of the pre-heat dish and the IR-lamp. Once the machine is cooling enough, cut off the power cable. 6 Attention ①When you maintain some large chip of the PCB board such as the mother board of the computer, you must pre-heat and dry the whole board first, then you can avoid the transmuting of the PCB board and soldering joint and rake angle of the chip. ②All the plastic plug-in board must be covered with aluminium-foil paper, to avoid transmutation or destroying. ③The PCB board which had been maintained, after cooling, clean it, and do the test when it is dry. If it is not ok, re-soldering it. ④Around working, when the PCB board is not on the holder, please do not long time open the IR-lamp, do not shoot the light on the strong glisten objects. Otherwise it will reduce its using time. ⑤About the chips which is encapsulation simply, please pre-stick aluminium-foil paper on the centre of the chip, to avoid burning out the slice of silicon. The measurement of the aluminium-foil paper had better a little larger than the slice of silicon, but not too large. Otherwise, it will do effect on the soldering.     Maintenance and Warning   Maintenance:  1.At all times – Insure the light body cooling fan is unobstructed and clean.   2.Use a little machine oil. Lubricate the focus holder and cell guide to inhibit rusting, keep them ease to operate.   3. Clean the Lamp body especially the lens and the pre-heat dish with the absolute alcohol, clean out the condensate of the welding flux. Keep the IR-thermal radiation without blocking.       Warning!   The T-870A System creates temperatures in excess of high degrees via Infrared Light. Wear appropriate eye protection or any device within the T-870A when using it. After use, Do not cut the power immediately, confirm the light body is cool-to-touch, cut the power, then place the system in airiness & safety storage.   Do NOT use this system or any associated device in an environment conducive to fire or electrical overload.   Disconnect the AC Power Plug when not in use.   When using, it is of high temperature, Do NOT allow children or the un-trained to touch the T-870A.     Cut off the power if it isn’t be used.   Statement：If there is any difference between user operating manual and actual product, according to the actual product !   Quility Certifications: CE, ISO9001, ISO2000,FC   Warrantee Terms All our soldering tool are provided one year warrantee by us from the date you make a purchase. An replacement or repairment will be provided by us for free when a faulty is developed within the warrantee.   Payment Terms Insurance is option to buyers. We highly recommend our dear buyers to insure for your order, because if the packages get missing, we will be not responsible for any lose (or damage) except for the insured ones. please make sure single payment for each item you won.We will combine the shipping. Please attached your telephone number when you payment so that we can post your package safety and smoothly.  :: Payment Methods We highly suggest using Paypal as it is safe and smooth. But other payment methods are available: WestUnion, Bank Transfer.    :: Shipping Terms We use the handling charge to cover our shipping department cost, packaging materials, fuel charges, boxes, and labels. Please do not bid if you don't agree with our shipping and handling prices.No Local pickup for auction customers. No third party shipping carrier will be used. Your item will be shipped in 1-2 working days after your payment is cleared. The shipping time is 5-7 working days. sometimes take a little longer, Due to Local dispatch Or other reasons. Return Policy If the item are in bad condition when it reach you, such as damage caused by transit, not working normally, parts loose, or any other fault, please contact us immediately, we will then be able to arrange replacement or repair. If  you are not satisfied the item you received,   we will take back your purchase, and we can  refund you the money you paid for the item, but shipping cost you paid can not be refunded, and we are not responsible for the incoming freight charges. Custom duty: We will do our best to reduce the custom duty. But the buyer is responsible for the custom duty once it occurs.  :: Shipping Methods We choose UPS, FEDEX, DHL and TNT as our cooperation partner to safely and speedy delieve your order.                               Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. Place a Bid!