HP\Agilent 70843B 12 Gbit/s Error Performance Analyzer Start Price USD 16,500.00 Current Price USD 16,500.00 Time Left - Bid Count 0 Buy It Now Price USD 16,995.00 Reserve Price - Start Time Thursday, August 28, 2008 End Time Thursday, September 04, 2008 Location Atlanta, GA Call Us See more about 'HP\Agilent 70843B 12 Gbit/s Error Performance Analyzer' Description Mr-Keyboard Platinum Power Seller Information - Questions? Call 770-253-6114 Ask for Chip or Trip This auction is for an Agilent 70843B 12 Gbit/s Error Performance Analyzer.Use the HP 71600 Series of Gbit testers to measure bit error ratio (BER) and to verify the performance and quality of your components and system hardware. This unit has the following applications: Lightwave submarine cable systems SONET/SDH synchronous network transmitters and receivers Gbit datacom serial links Lasers and photodetectors High-speed logic devices Optical amplifiers and modulators Decision circuits Multiplexers and output driversFor high-performance pattern generation and error analysis across the entire 100 Mb/s to 12 Gb/s range, use an HP 71612B error performance analyzer with optional low-rate clock. Both pattern generator and error analyzer provide a wide range of PRBS and user-defined patterns, with versatile triggering facilities. And to help you identify the address of the errored bits use optional error location analysis. Once the position of an errored bit is identified, the flexible triggering features can be used to view the errored pattern on an oscilloscope for further diagnosis. Error Location Analysis Makes it easier for you to find the source of systematic errors — Vital when you’re under continuous pressure to develop more reliable high-speed components and subsystems. Bit BER Locate the cause of systematic errors causing a specific bit to change value. Just specify any bit in a user-defined pattern and perform bit error measurements upon it Block BER Essential when trying to locate the cause of systematic errors which affect longer runs of bits, for example a corrupt header in a SONET or SDH frame. Perform bit error rate measurements on a range of bits within a user-defined pattern Error-location capture Helps you discriminate between random and systematic errors.In a user-defined pattern,automatically highlight the position of each errored bit in turn displaying the address of the errored bit and show the surrounding bit pattern. Then automatically measure BER of each errored bit. If the error rate of a captured bit remains significant over a period,there is probably a pattern dependent, systematic errorThis unit has the following specifications: Test patterns PRBS: 2 to the 31 -1, 2 to the 23 -1, 2 to the 15 -1, 2 to the 10 -1, 2 to the 7 -1. User-defined pattern: Up to 8 Mbit. Zero substitution: Extends the longest run of zeros up to pattern length less one bit on patterns 2 to the 13, 2 to the 11, 2 to the 10, 2 to the 7. Variable mark density ratio: 1/8 to 7/8 in 1/8 steps on patterns 2 to the 13, 2 to the 11, 2 to the 10, 2 to the 7. STM-64 and OC-192 patterns: Samples supplied on disk along with other stress patterns.In the pattern generator,any pattern may be split into two equal-length patterns, with hitless switching between them.The user-defined patterns may be loaded from, or saved to, a 3-½inch,MS-DOS ® format floppy disk. Pattern generator There are inputs for an external clock, external error inject, alternate-pattern switch and data output on/off switch. There are outputs for clock and inverted clock, data and inverted data and pattern trigger, sub-rate (quarter-rate)clock; also four outputs for quarter-rate data. Clock input Frequency range: 100 MHz to 12 GHz Interface: 0.45 to 0.90 V p-p, dc coupled, 50 ohms. (=10 GHz), 0.65 to 0.9 V p-p (>10 GHz) Clock outputs – main Frequency range: 100 MHz to 12 GHz Interface: Complementary, dc coupled, 50 ohms, reverse terminated. (Independent control of outputs available) Amplitude:0.5 to 2 V p-p in 10 mV steps Range: +1.5 to -3.0 V in 10 mV steps Data outputs – main Interface: Complementary, dc coupled, 50 ohms, reverse terminated NRZ, normal or inverted. (Independent control of outputs available) Amplitude: 0.5 to 2 V p-p in 10 mV steps Transition times (10%to 90%): <30 ps (typical at 2 V p-p) Jitter: < 20 ps p-p; < 15 ps p-p at 10 Gb/s Range: +1.5 to -3.0 V in 10 mV steps Clock/data delay: ±1 ns (100 MHz to 500 MHz),one clock period (500 MHz to 12 GHz) Resolution: 1 ps Clock and data outputs – subrate Frequency range: 1/4 of main clock rate Interface: dc coupled, 50 ohms, reverse terminated Amplitude: 0.5 to 1 V p-p in 10 mV steps Range: 0 to -2.0 V in 10 mV steps Trigger output: Pattern; clock/32; clock/8 Error add Internal: Single on command, or fixed ratio 1 in 10 n bits, where n =3 to 9 External: TTL levels (active low) Error detector The error detector has clock and data inputs and an input which inhibits error counting. There are outputs for errors and pattern trigger. The error detector has both manual and automatic setting of decision threshold and clock/data phase alignment. Clock input Frequency range: 100 MHz to 12 GHz Interface: 0.45 to 0.90 V p-p dc coupled, 50 ohms to 0 V or -2 V Sensitivity: < 200 mV p-p (typical at 10 Gb/s) Data input Sensitivity: < 50 mV p-p (typical for 2 to the 23 -1 PRBS input at 10 Gb/s. 0 V high level) Impedance: 50 ohms to 0 V or -2 V, dc coupled Decision threshold range: +1 to -3 V in 1 mV steps Clock/data phase alignment: ±1 ns (100 MHz to 500 MHz); 1 clock period (500 MHz to 12 GHz) Resolution: 1 ps Trigger output: Pattern or clock/8 Error output: 0 to -0.4 V nominal Measurement modes:Manual, single period, repetitive period Measurement period: 1 s to 100 days 10, 100, 1000 errors; 10 to the 7 to 10 to the 15 bits Pattern synchronization: Automatic or manual Selectable threshold: 1 to the -1 to 10 to the -8 Audible output: Proportional to error ratio Result logging: Time-stamped results to an external printer Clock source Option UHF = Clock Source Not IncludedThis unit has the following options installed: UHF: 0.1 to 12 Gb/s error performance analyzer with pattern generator and error detector (no clock source provided) UHJ: Adds enhanced error location analysis to help identify sources of systematic errors.This auction includes an Agilent 70843B. It was part of an Agilent 71612B Error Analysis system. This auction does not include an Agilent 70004A Mainframe or a clock source.This unit requires a shipping crate, which is an additional $100.This item is in excellent condition, working perfectly, and comes with a 14 Day Guarantee Against DOA. Terms - Questions? Call 770-253-6114 Ask for Chip or Trip Use the Rate Calculator located at the bottom of the page to select your desired shipping method. Priority Service is available, but not listed. All items will be professionally packed and shipped. Insurance is required on all shipments. Shipping Carrier is at our discretion. WE WILL NOT SHIP ON YOUR ACCOUNT. International bidders, excluding Canada, must Contact Us before bidding. Please supply your complete mailing address, so we can determine the shipping cost. You are bidding on the item(s) described in the ad and shown in the photos only, any items not listed in the description or shown in the photos are not included. Warranty period begins the day item is received. Our 14 Day Guarantee Against DOA (Dead On Arrival) does not guarantee compatibility. If something is listed AS-IS, there are absolutely no returns, refunds, or exchanges. If you receive an item that we have guaranteed against DOA, and it is Dead On Arrival, please notify us immediately. We will then instruct you on how to return the item for an exchange or refund at our discretion. If an item is returned for any reason other than it not working, we will impose a 15% restocking fee. We will not accept any returns without an RMA Number on the box, we will provide you with an RMA number when we discuss your return. International Customers: Please be aware, if you are returning an item we do not refund shipping/handling or bank fees. You are responsible for returning the item and paying for return shipping. Terms are Non-Negotiable. Full payment must be received within 7 days of auction close. If after 7 days payment has not been received, then we will notify eBay of a non-paying bidder and relist the item(s). Items shipping within Georgia are subject to 7.00 % sales tax. AcceptedCashier's Check, Company Check, Money Order, and Personal CheckBank Wire - Contact for InformationCredit Card - Must Call 770-253-6114 Before Bidding to use Not AcceptedCOD and Paypal If the auction price is over $2,000.00, then we only accept Company Checks, Personal Checks, Money Orders, Bank Wires, and Cashier's Checks. AcceptedBank Wire - Contact for Information Not AcceptedCashier's Check, COD, Company Check, Credit Cards, Money Order, Paypal, and Personal Checks Email: Chip@ecrunch.comTelephone: 770-253-6114Fax: 404-759-2592 Address:SandersAttn: Chip Sanders2 Greenville St.Newnan, GA 30264 Place a Bid!