Concrete business forms trucks crane finishing equip Start Price USD 75,000.00 Current Price USD 75,000.00 Time Left - Bid Count 0 Buy It Now Price - Reserve Price - Start Time Sunday, July 06, 2008 End Time Sunday, July 13, 2008 Location Fort Atkinson, WI See more about 'Concrete business forms trucks crane finishing equip ' Description We are selling off our concrete related equipment to focus on our other operations. There is enought stuff here to pour atleast one wall & do the flatwork to boot. I will try to list as much & as accurately as I can.  I have more pictures of everything I just could not put them on due to a 12 picture limit. If we cannot sell as a whole we will piece it out or have an onsite auction. You are incouraged to come & look drive etc. there is to much to list. Feel free to make an offer on all or parts.  All offers will be considered 1984 IH S1900 crane truck / boom truck with model 666 A National crane 12.5 ton capacity. Stick is 66' we also have a 42' jib for it for a 108' of crane w/ hydraulic hose real. truck has a DT466 IH turbo charged engine with a 13 spd fuller roadranger trans., air brakes , 8' wide x 18' long bed crane controls on both sides. will lift 18 sets of 9' forms at a time at 66'. Truck is loaded & ready for work. 1986 GMC brigidare w/ 350 cummins 13 spd , air brakes , 8' wide X 24' long bed with 25' cascade model 50C knuckle boom on back (needs outrigger cylinder seals replased) capacity of 8250.  We are the 2nd owner of this truck & the miles on it are original. This is a very good strong truck ready to go. Has 19,000# front axle & 44 or 48,000# rear axles. 1983 IH footing truck w/ IH Dt 466 turbo charged engine w/ 4 spd allison automatic trans, bench seat, 3 utility boxs, & 1 large storage box. Bed is 8' wide X 18' long. Set up to slide a bunk of form-a-drain in on drivers side, re-rod slides in the back on the bottom so you can get to it, 18-20' 2x6's slide in on the bottom (will hold lots), etc. form oiler & generator on the back Truck was put together 2 years ago. Tires excellent, has air brakes, ready to work. 1985 GMC 6000 (white truck) has a 8.2L turbocharged detroit (good power smokes until warmed up) This truck has been mutipurpose, it used to be our footing truck, then we used it for flatwork cause it pulls a bobcat trailer with ease, & has lumber racks on passinger side. Last we used it to haul additional 4' & 6' forms when needed. It has a 5 speed trans. with a 2 spd. rear axle. We have not used it in about 1 year, but it ran & drove excellent (better than it looks).  While it was parked someone broke the shifter off to steal the 2 spd. axle switch, we fixed the shifter, but don't have the switch, this one has hydraulic brakes so it may have some brake line issues to get back on the road, so It needs some work. 1994 Ford super duty (maroon) w/ powerstroke diesel & 5 spd.with overdrive transmission. This was a footing truck until we built our IH truck. Has a heavy duty lumber rack & storage bed on it.  will need some work, has some oil leaks, clutch & transmission need work & is smoking more than it used to. 1988 Ford 450 7.3L 5 spd. w/ overdrive transmission used for flat work & pulling skid steer around still driven every day. Has flatbed on it with a storage box for tools, 4th gear grinds. Trucks come loaded as you see them. Duraform & symon Concrete forms: 5 bar X 9' tall wall forms 260-2'x9' panels, 4-22" panels, 4-20" panels, 6-18" panels, 32-16" panels, 2-15" panels, 41-14" panels, 2-13" panels, 40-12" panels, 4-11" panels, 10-10" panels, 18-9" panels, 14-8" panels, 4-7" panels, 12-6" panels, 12-5" panels, 12-4" panels, 9' Steal corners: 30 4"x4" inside corners, 24 1"x1" outside corners, 4 reversible 4"x6" corners, 2-2"x2" offset , 2-swing corners, 15-45 degree inside corners, 5-45 degree corners for 10" walls, 4-45 degree outside corners for 8" walls, 8' wall stuff 2-20" panels, 2-16" panels, 10-14" panels, 6-10" panels, 2-9" panels, 2-8" panels 8' steal corners: 2-6"x6", 1-swing, 8-4"x4", 4-1"x1". 7' walls forms: 20-2'x7' panels. 6' wall forms: 42-2'x6' panels 5' wall forms: 14-2'x5' panels 4' 2 bar wall forms: 232-2'x4' panels, 2-22"x4', 6-20"x4', 5-18"x4', 26-16"x4', 2-15"x4', 37-14"x4', 2-13"x4', 84-12"x4', 2-11"x4', 14-10"x4', 36-9"x4', 34-9"x4', 32-8"x4', 8-6"x4', 8-4"x4' 4' 2 bar steal corners: 43-4"x4" inside corners, 24-1"x1" outside corners, 15-4"x6" inside corners, 5-2"x2" corners, 7-swing corners, 6-inside 45 degree corners, 11-45 degree corners. Hardware: Scafold brackers:5 pails, line up rail brackets- pails, stacking plates- pails 5+, 22.5 degree for radius walls 150+, 45 degree clips, 50, e clips 50+, offset clips 50+ & more. 10 boxes of 10" wall ties, 4 boxes of 8" wall ties, 1 box of 12" wall ties, & more. 20+ boxes of anchor bolts. 300+ steal stakes. Lots of lumber (2x4, 2x6), brickledge, stacking blanks, 6 rolls of 6 mill plastic 2000 sq. ft. roll. Form-a-drain boards & fittings 10 rolls of 4" tile 10 bags of 3" tee's for bleaders (50 per bag) 3- 4'x5' steel window wells 1/2 ton of 1/2" re-rod Lazer for setting grade Whiteman 4' power trowel Allen razorback 36" power trowel Magic screed Vibeberstrike screed, almost new, but has a bent head. Softcut brand electric concrete saw 10' bull float & handle Lots & lots of stuff & misc & more. Everything is sold as is, but buy it to go to work, and make some money, this is a huge lot & is pretty much everything needed to start a concrete wall business. I put some pictures of a poured wall & a wall formed up, these were done with these forms & equipment. Buyer to pay by certified funds or cash within 10 days of auctions end. Equipment to be removed within 60 days of auctions end. There will be a non-refundable deposit of 10% of final price required within 48 hours of auctions end Unless other arrangements are made. Please ask questions           Place a Bid!